Get premium membership and access questions with answers, video lessons as well as revision papers.
a) Final drive unit -changes the drive from the propeller shaft to that of half shafts through 90
Allows easier cornering of the vehicle by allowing the inner wheel to move at a reduced speed while the outer wheel is speeded.
It increases the torque output of half shafts by reducing the speed of the propeller shaft by use of a small pinion to drive the larger crown wheel.
b) Clutch -connects and disconnects the drive between the engine and the gear box. – it enables the drive to be taken up gradually and smoothly
-it provides the vehicle with a temporary neutral.
marto answered the question on September 18, 2019 at 09:07
- The figure below shows an isometric drawing of a machine component. Draw FULL SIZE, in first projection the following views in the drawing paper provided.(Solved)
The figure below shows an isometric drawing of a machine component. Draw FULL SIZE, in first projection the following views in the drawing paper provided.
a) Sectional front elevation B-B .
b) The plan.
c) Include 3 important dimensions.
Do not show hidden details
Date posted: September 18, 2019. Answers (1)
- State two functions of each of the following vehicle systems .
i) suspension system
ii) steering system
iii) braking system(Solved)
State two functions of each of the following vehicle systems .
i) suspension system
ii) steering system
iii) braking system
Date posted: September 18, 2019. Answers (1)
- Explain each of the following terms as used in power mechanics
i) Detonation
ii pre- ignition
iii) Atomization(Solved)
Explain each of the following terms as used in power mechanics
i) Detonation
ii pre- ignition
iii) Atomization
Date posted: September 18, 2019. Answers (1)
- State two types of fire extinguishers used to put out a burning carburetor.(Solved)
State two types of fire extinguishers used to put out a burning carburetor.
Date posted: September 18, 2019. Answers (1)
- Identify two advantages of a pressurized water cooling system over thermo-siphon cooling system.(Solved)
Identify two advantages of a pressurized water cooling system over thermo-siphon cooling system.
Date posted: September 18, 2019. Answers (1)
- State two possible causes why a petrol engine would emit white or light blue smoke at its exhaust pipe.(Solved)
State two possible causes why a petrol engine would emit white or light blue smoke at its exhaust pipe.
Date posted: September 18, 2019. Answers (1)
- State two requirements for combustion in a diesel engine.(Solved)
State two requirements for combustion in a diesel engine.
Date posted: September 18, 2019. Answers (1)
- Give two reasons why bearings are necessary.(Solved)
Give two reasons why bearings are necessary.
Date posted: September 18, 2019. Answers (1)
- State two possible causes of a clutch slip.(Solved)
State two possible causes of a clutch slip.
Date posted: September 18, 2019. Answers (1)
- State four physical checks that need to be carried on a car battery.(Solved)
State four physical checks that need to be carried on a car battery.
Date posted: September 18, 2019. Answers (1)
- State one cause of each the following excessive tire tread wear patterns .
i) feathered edge
ii) shoulder wear(Solved)
State one cause of each the following excessive tire tread wear patterns .
i) feathered edge
ii) shoulder wear
Date posted: September 18, 2019. Answers (1)
- Differentiate between friction and antifriction bearings. Give one example of each type.(Solved)
Differentiate between friction and antifriction bearings. Give one example of each type.
Date posted: September 18, 2019. Answers (1)
- State one use of each of the following tools
a) Piston ring compressor
b) Micrometers
c) stethoscope
d) Compression gauge
(Solved)
State one use of each of the following tools
a) Piston ring compressor
b) Micrometers
c) stethoscope
d) Compression gauge
Date posted: September 18, 2019. Answers (1)
- For each of the following components state two measurements which should be taken during inspection.
a) Crankshaft
b) Piston rings(Solved)
For each of the following components state two measurements which should be taken during inspection.
a) Crankshaft
b) Piston rings
Date posted: September 18, 2019. Answers (1)
- State two reasons for alloying metals.(Solved)
State two reasons for alloying metals.
Date posted: September 18, 2019. Answers (1)
- Explain the following terms as used in the suspension system.
a) sprung weight
b) un sprung weight(Solved)
Explain the following terms as used in the suspension system.
a) sprung weight
b) un sprung weight
Date posted: September 18, 2019. Answers (1)
- Differentiate between live and dead axle.(Solved)
Differentiate between live and dead axle.
Date posted: September 18, 2019. Answers (1)
- Arrange the following personnel training levels in the correct order starting with the highest, (2marks)
Technician, Craftsman, Technologist, Artisan(Solved)
Arrange the following personnel training levels in the correct order starting with the highest, (2marks)
Technician, Craftsman, Technologist, Artisan
Date posted: September 18, 2019. Answers (1)
- List three major components of the diesel fuel system.(Solved)
List three major components of the diesel fuel system.
Date posted: September 18, 2019. Answers (1)