-Cutting very wide curve leading to waste
-Using a lot of energy to cut
-Split the grain when finishing the cut
Kavungya answered the question on October 18, 2019 at 10:27
- Name two types of jaws in a brace and state when each is used.(Solved)
Name two types of jaws in a brace and state when each is used.
Date posted: October 18, 2019. Answers (1)
- Give two reasons why edge moulding are used at the edge of manufactured boards when making table top. (Solved)
Give two reasons why edge moulding are used at the edge of manufactured boards when making table top.
Date posted: October 18, 2019. Answers (1)
- Name the SI unit for the measurement used when buying the following.
-Nails …………………………………….
-Timber …………………………………..
-Manufactured boards …………………..
-Screws ………………………………….
-Varnish …………………………………
-Sand paper ………………………….….(Solved)
Name the SI unit for the measurement used when buying the following.
-Nails …………………………………….
-Timber …………………………………..
-Manufactured boards …………………..
-Screws ………………………………….
-Varnish …………………………………
-Sand paper ………………………….….
Date posted: October 18, 2019. Answers (1)
- a)The shape shown in the figure below is made using a piece of timber
Indicate by the use of arrows the direction of smoothening the curve...(Solved)
a)The shape shown in the figure below is made using a piece of timber
Indicate by the use of arrows the direction of smoothening the curve using spoke shave
b)By use of neat sketches show the kerf made by rip and cross cut saws.
Date posted: October 18, 2019. Answers (1)
- Name the solvent used for the following finishes
i) Oil paint
ii)Emulsion paint(Solved)
Name the solvent used for the following finishes
i) Oil paint
ii)Emulsion paint
Date posted: October 18, 2019. Answers (1)
- What is scale drawing? (Solved)
What is scale drawing?
Date posted: October 18, 2019. Answers (1)
- State three categories of pictorial drawing. (Solved)
State three categories of pictorial drawing.
Date posted: October 18, 2019. Answers (1)
- Give THREE necessary requirements for self employment in wood industry. (Solved)
Give THREE necessary requirements for self employment in wood industry.
Date posted: October 18, 2019. Answers (1)
- By means of neat sketches show three natural and two seasoning timber defects.(Solved)
By means of neat sketches show three natural and two seasoning timber defects.
Date posted: October 18, 2019. Answers (1)
- Name the parts of the tool shown A…………B………………C………(Solved)
Name the parts of the tool shown
A…………………………
B…………………………
C………………………
Date posted: October 18, 2019. Answers (1)
- Give two advantages that oil has over water as a sharpening agent on the oil stone (Solved)
Give two advantages that oil has over water as a sharpening agent on the oil stone
Date posted: October 18, 2019. Answers (1)
- State four requirements of a good finishing room. (Solved)
State four requirements of a good finishing room.
Date posted: October 18, 2019. Answers (1)
- Give the necessary precaution that you should observe when:
a)Using a chisel
b)Using a mallet(Solved)
Give the necessary precaution that you should observe when:
a)Using a chisel
b)Using a mallet
Date posted: October 18, 2019. Answers (1)
- Briefly explain the steps followed in the making of a haunched mortise and tenon joint.(Solved)
Briefly explain the steps followed in the making of a haunched mortise and tenon joint.
Date posted: September 23, 2019. Answers (1)
- Using sketches of exploded views show five different ways of making widening joints.(Solved)
Using sketches of exploded views show five different ways of making widening joints.
Date posted: September 23, 2019. Answers (1)
- Name five different widening and four framing joints used in woodwork.(Solved)
Name five different widening and four framing joints used in woodwork.
Date posted: September 23, 2019. Answers (1)
- Name two types of machines used in shaping (decorating) wood and two types used for cut out different types of joints.(Solved)
Name two types of machines used in shaping (decorating) wood and two types used for cut out different types of joints.
Date posted: September 23, 2019. Answers (1)
- List down five different tasks that can be done using a circular rip saw in woodwork.(Solved)
List down five different tasks that can be done using a circular rip saw in woodwork.
Date posted: September 23, 2019. Answers (1)
- Name any five types of machines used in woodwork besides a circular rip saw.(Solved)
Name any five types of machines used in woodwork besides a circular rip saw .
Date posted: September 23, 2019. Answers (1)
- Outline the procedure of finishing using French polish.(Solved)
Outline the procedure of finishing using French polish.
Date posted: September 23, 2019. Answers (1)